PFTL101AER 1KN 3BSE023011R1工控

产品标题：PFTL101AER 1KN 3BSE023011R1工控

型号：PFTL101AER 1KN 3BSE023011R1

品牌： ABB

质保：七天验收期，质保期一年

交货期： 1-3个工作日

产品图片展示

产品详情资料：

PFTL101AER 1KN 3BSE023011R1

以太网全局数据功能以太网NIU通过以太网全局数据交换与其控制器通信。一个交换机用于将输出发送到以太网NIU，另一个交换机则用于将输入发送回控制器。PFTL101AER 1KN 3BSE023011R1以太网NIU还可以使用以太网全局数据交换从PACSystems RX3i控制器接收以下COMMREQ命令：? Modbus主站-功能代码1、2、3、4、5、6、7、15、16、17? Genius–启用/禁用输出，切换BSM，清除故障，清除所有故障，分配***，读取诊断? PROFIBUS主站-COMMREQ 1、2、4、5、6? 运动（PFTL101AER 1KN 3BSE023011R1）-负载参数? 高速计数器-数据命令? DeviceNet主设备-COMMREQ 1、4、5、6、7、9? 模拟模块-HART协议COMMREQ以太网NIU执行COMMREQ，并使用另一个以太网全局数据交换将结果发送回RX3i。16.15.5端口NIU有两个单独的板载串行端口，可通过模块正面的连接器访问。PFTL101AER 1KN 3BSE023011R1这些端口为外部设备提供串行接口。端口1（COM1）是一个DCE端口，允许一根简单的直通电缆与标准AT型RS-232端口连接。它有一个带标准引脚输出的9引脚阴性D子连接器。端口2（COM2）是一个与RS-485兼容的DCE端口。端口2有一个15针内螺纹D形接头。以太网NIU没有以太网端口。以太网通信由位于I/O站的一个或多个以太网变送器模块（本章前面介绍过）提供

产品英文详情资料：

Ethernet Global Data Features The Ethernet NIU communicates with its controller via Ethernet Global Data exchanges. One exchange is used to send outputs to the Ethernet NIU and another exchange is used to send inputs back to the controller. The Ethernet NIU can also use Ethernet Global Data exchanges to PFTL101AER 1KN 3BSE023011R1receive the following COMMREQ commands from a PACSystems RX3i controller: ? Modbus Master – function codes 1, 2, 3, 4, 5, 6, 7, 15, 16, 17 ? Genius – enable/disable outputs, switch BSM, clear fault, clear all faults, assign monitor, read diagnostic ? PROFIBUS Master – COMMREQs 1, 2, 4, 5, 6 ? Motion (DSM314/DSM324) – load parameters ? High-Speed Counter – Data command ? DeviceNet Master – COMMREQs 1, 4, 5, 6, 7, 9 ? Analog The module – HART Protocol COMMREQs The Ethernet NIU executes the COMMREQ and sends the results back to RX3i using another Ethernet Global Data exchange. 16.15.5 Ports The NIU has two independent, on-board serial ports, PFTL101AER 1KN 3BSE023011R1accessed by connectors on the front of the module. These ports provide serial interfaces to external devices. Port 1 (COM1) is a DCE port that allows a simple straight-through cable to connect with a standard AT-style RS-232 port. It has a 9-pin, female, D-sub connector with a standard pin out. Port 2 (COM2) is a DCE port that is RS-485 compatible. Port 2 has a 15-pin, female D-sub connector. The Ethernet NIU does not have an Ethernet port. Ethernet communications are provided by one or more Ethernet Transmitter Modules (described previously in this chapter) located in the I/O StationPFTL101AER 1KN 3BSE023011R1